[PLF69]

Originally Posted by somer

Anyone dig into why the axle output shaft part numbers are different?

ECS gives: "M3 CS Axles - higher temp resistance for hard track use
Can be used as a replacement higher-performance axle for track vehicles per BMW. These are the axles from the M3 CS"

sounds like just random fluff they put in the description of the part.

My impression looking under the CSL on a lift was the shafts looked beefier than on the M4C I had before.

[wavyyyy]

I tried ordering a strut brace from Schmeidmann, they informed me that they're waiting on stock. This was about a week ago, still waiting on a response.

[Bee Pee]

Originally Posted by swagon

They've certainly got them for G20/21 xDrive cars so I reckon there are G8x ones available but I'll confirm that and the brace in a few days.

OEM xdrive minus hub carriers/knuckles standard fit on G8x CS - part nos are

312178836 41 (Left) and 42 (Right)

Ca. 426usd/side

[Asymmetrick]

Anyone knows when/if we can expect to see all the parts of the 3.0 CSL on ETK?

Some parts of that car have been listed on ETK (as a specialized variant of the G82 M4 -> 3.0 CSL S58O). However, there is still a lot missing.

[swagon]

Originally Posted by Asymmetrick

Anyone knows when/if we can expect to see all the parts of the 3.0 CSL on ETK?

Some parts of that car have been listed on ETK (as a specialized variant of the G82 M4 -> 3.0 CSL S58O). However, there is still a lot missing.

I think it's self-explanatory if/why 3.0 CSL parts will never appear in ETK.

[swagon]

Originally Posted by bee pee

with g80 cs x drive now out i assume there must be awd knuckles now that add front -ve camber - anyone know part nos yet ?

31 21 7883641+2

[swagon]

M3 CS parts that are specific or carry-over from CSL:

front+rear springs
front dampers 31317888597+8
front anti-roll bar 31358091425 (same as G81)
mid-pipe 18305A69053
muffler same as CSL
steering wheel same as CSL
rear driveshafts same as CSL
rear dampers same as G81/G87
front grille 51138087848

no front lip numbers yet

[Asymmetrick]

Originally Posted by swagon

I think it's self-explanatory if/why 3.0 CSL parts will never appear in ETK.

Unless I am mistaken, the new/upcoming EU right to repair law would obligate BMW to provide parts lists of all their products, including the 3.0 CSL, in the eventuality that repairs are required.

I appreciate that that the ~50 units produced by BMW are likely to sit in museum-like garages, but regulations would still apply to these cars.

Let me know if I am missing some other factor that falls under the "self-explanatory" category.

[somer]

Has anybody checked to see if there are any software steering changes that could be coded in like they were with the M4 GTS? Also what about damper settings (may require the actual physical shocks to work correctly)? Guessing there might be different settings for CSL and CS.

[Hit_Apex]

Originally Posted by Asymmetrick

Unless I am mistaken, the new/upcoming EU right to repair law would obligate BMW to provide parts lists of all their products, including the 3.0 CSL, in the eventuality that repairs are required.

I appreciate that that the ~50 units produced by BMW are likely to sit in museum-like garages, but regulations would still apply to these cars.

Let me know if I am missing some other factor that falls under the "self-explanatory" category.

I'm sure the car comes with a concierge or internal contact that would coordinate repair and part requests in a manner that exceeds any regulatory requirement. M Motorsports clients have an online portal to access parts and the various program vendors. Could be similar to that too.

Just a guess but want to bump this thread anyway...

[TVonthe80]

i was digging through some of the parts on BMW NW and noticed that the engine and transmission mounts for the CS appear to be the same as the Comp. Only the CSL and 3.0 were shown as having unique engine mounts.

That's interesting if accurate as it would mean the only difference in drivetrain feel is coming from the tuning

[somer]

Originally Posted by TVonthe80

i was digging through some of the parts on BMW NW and noticed that the engine and transmission mounts for the CS appear to be the same as the Comp. Only the CSL and 3.0 were shown as having unique engine mounts.

That's interesting if accurate as it would mean the only difference in drivetrain feel is coming from the tuning

Tranny mount is different

22327884147 (CS)
22326866514 (CP X-Drive)

But yea, engine mounts are the same

[TVonthe80]

Originally Posted by somer

Tranny mount is different

22327884147 (CS)
22326866514 (CP X-Drive)

But yea, engine mounts are the same

interesting, that 4147 PN looks like it is also the X3M trans mount. Most places I checked either don't have it listed or say it was discontinued.

https://www.bmwoemparts.com/oem-part...nt-22327884147

[somer]

Originally Posted by TVonthe80

interesting, that 4147 PN looks like it is also the X3M trans mount. Most places I checked either don't have it listed or say it was discontinued.

https://www.bmwoemparts.com/oem-part...nt-22327884147

Yeah, seems like X3M LCI mount as well. BMW-ETK isn't infallible, sometimes you just never know for sure.

[elitez]

Originally Posted by swagon

CSL bucket seats part numbers:

52 10 7887708 x1 cfrp seat frame
52 10 7887707 x1
52 10 7887712 x1 inner cushion
52 10 7887711 x1
52 10 7887714 x1 outer cushion
52 10 7887713 x1
52 10 7887716 x1 side bolster thing
52 10 7887715 x1
52 10 7887706 x2 bottom cushion
52 10 7887717 x2 headrest
52 10 7883320 x2 badge
52 10 8067477 x2 ballsack divider
52 10 7887709 x1 seat rail
52 10 7887710 x1
52 10 8087904 x2 idk
51 47 9908579 x8 screws
07 11 9906215 x8 washers

I will put them in the main post later

Would you know a part # for the completed CF CSL bucket Seats?!

[VIERsr]

Do we know the weight of 827m wheels?

[FranckF1]

Hi guys,

Great news, I wanted to wait to have one in my hand before telling the forum, but you can now have the CS/CSL steering wheel without all the buttons.
I paid just over 800 euros (in France) for mine

Part number is 32307874035
Don't need to buy anymore the full CS/CSL wheel at 2k$+

[GT3M2]

Has anyone installed the minus knuckles on a car?

-GT3M2

[swagon]

Originally Posted by GT3M2

Has anyone installed the minus knuckles on a car?

-GT3M2

quite a few people have on F8x. Alpina does it on their G20s.

[elitez]

Any one have the part # for the CSL side vent emblems?

[as7920]

Originally Posted by FranckF1

Hi guys,

Great news, I wanted to wait to have one in my hand before telling the forum, but you can now have the CS/CSL steering wheel without all the buttons.
I paid just over 800 euros (in France) for mine

Part number is 32307874035
Don't need to buy anymore the full CS/CSL wheel at 2k$+

Was looking at that myself today.

I can't tell from your pic, but could you confirm the stitching is M Tricolour or M Performance white?

Cheers.

[FranckF1]

Sorry for the delay. It's M Tricolour