[Dnshift]

Originally Posted by M3Geneva

Strut Brace install and some carbon parts 😁

Looks great! What strut brace and front badge is that?

[Gang80]

Ebay Clutch Stop, but who wants to see a picture of that

[MaC-N54-E82]

Had the wheels ceramic coated. This combined with the iSweep2000 pads should make detailing much, much easier.

[TaroBaapG35]

Originally Posted by Gang80

Ebay Clutch Stop, but who wants to see a picture of that

How many of the 'discs' did you end up using? I think the BMS comes with 5 and I'm reading that 3 is good enough?

Finally got the SST controller in from mike@x-ph.com. Took around 45 mins to install. Had to lift up driver rear side to make it easier to get to wires. Did end up losing the driver grommet in the blank black box but passenger one was saved. Used electrical tape to seal the open side for now and will check to see if SA can get me one or I might just get a generic one from Lowes and make it work.

Programmed A (Open) and C (Stock) to homelike. Might change C to B (Closed) in future. Worked well on my quick 10min drive.

[vettejunkie23]

Originally Posted by TaroBaapG35

How many of the 'discs' did you end up using? I think the BMS comes with 5 and I'm reading that 3 is good enough?

Finally got the SST controller in from mike@x-ph.com. Took around 45 mins to install. Had to lift up driver rear side to make it easier to get to wires. Did end up losing the driver grommet in the blank black box but passenger one was saved. Used electrical tape to seal the open side for now and will check to see if SA can get me one or I might just get a generic one from Lowes and make it work.

Programmed A (Open) and C (Stock) to homelike. Might change C to B (Closed) in future. Worked well on my quick 10min drive.

Still waiting on SST controller from mike@x-ph.com. I did however order 2 BMW Blind Plugs (35mm) based on people dropping them into the black abyss.

https://www.pelicanparts.com/More_In...-7-140-849-BOE

[ash_schwin]

Washed and waxed the car and added this sticker

[DTMfan]

Originally Posted by Burrcold

PPF, ceramic coating, and ceramic tint. I can finally start picking my nose again in the car.

What tint level did you go with?

[Burrcold]

Originally Posted by DTMfan

What tint level did you go with?

35% sides and back, 50% windshield (all Xpel ceramic).

[mike@x-ph.com]

Originally Posted by TaroBaapG35

Finally got the SST controller in from mike@x-ph.com. Took around 45 mins to install. Had to lift up driver rear side to make it easier to get to wires. Did end up losing the driver grommet in the blank black box but passenger one was saved. Used electrical tape to seal the open side for now and will check to see if SA can get me one or I might just get a generic one from Lowes and make it work.

Programmed A (Open) and C (Stock) to homelike. Might change C to B (Closed) in future. Worked well on my quick 10min drive.

Congrats

Originally Posted by vettejunkie23

Still waiting on SST controller from mike@x-ph.com

All pre-orders are already on the way and any new order will ship within 24 business hours from our Las Vegas warehouse

[DTMfan]

Originally Posted by Burrcold

35% sides and back, 50% windshield (all Xpel ceramic).

Thanks! Any pics in the daylight from the side? Looks great! I'm waffling if 35% is too light with a 70% windshield. I'm used to 15% and 20% tint on my cars.

[Aalfred]

Originally Posted by TaroBaapG35

How many of the 'discs' did you end up using? I think the BMS comes with 5 and I'm reading that 3 is good enough?

Finally got the SST controller in from mike@x-ph.com. Took around 45 mins to install. Had to lift up driver rear side to make it easier to get to wires. Did end up losing the driver grommet in the blank black box but passenger one was saved. Used electrical tape to seal the open side for now and will check to see if SA can get me one or I might just get a generic one from Lowes and make it work.

Programmed A (Open) and C (Stock) to homelike. Might change C to B (Closed) in future. Worked well on my quick 10min drive.

Looks like you did the same mistake I did and lost the grommet in the abyss. I used duct tape to seal the opening but saw the replacement grommet posted above and will order them. Its easier to reinstall it if you flit the grommet and push the smaller opening into the wheel well side.

[moonluv810]

Originally Posted by ash_schwin

Washed and waxed the car and added this sticker

Loving this!

[TaroBaapG35]

Originally Posted by Aalfred

Looks like you did the same mistake I did and lost the grommet in the abyss. I used duct tape to seal the opening but saw the replacement grommet posted above and will order them. Its easier to reinstall it if you flit the grommet and push the smaller opening into the wheel well side.

Yea If my local dealership doesn't have it during my breakin service Tuesday, I'll order it from the post above.

Reinstall was def straight forward since I had the grommet cut to fit the wires.