[Mapper]

Wheel is a 20x10.5 ET10. Thought Id be good but with F1 supercar 3 tires I feel im out too far using 295s
What do you think?
The front are 20x10 ET12 with 285 suoercar 3 and shocking.. no rubbing on the fins.

[gc.g80brg]

you need a drop of course and neg cambe. this look like a F-150 as is :P !

[Mapper]

Lowering is on the list... f150 lol.

[Howard1485]

Well I was going to say F350 but love the wheels!

[Tobster3]

@Mapper Looks great!!

I went with the below which is very similar spec. I will be installing Eibach Front springs only.

Front - 10.5x20 ET14 285/30 R20
Rear - 11x20 ET12 295/30 R20

Only have a few pics as I took it straight from the dealer to get PPF/ tint etc.

[Mapper]

Originally Posted by Tobster3

@Mapper Looks great!!

I went with the below which is very similar spec. I will be installing Eibach Front springs only.

Front - 10.5x20 ET14 285/30 R20
Rear - 11x20 ET12 295/30 R20

Only have a few pics as I took it straight from the dealer to get PPF/ tint etc.

Interesting. Looks amazing by the way.
11 rear et12 is same as approx.5x ET6...
And your tire choice 295 must be narrower than the f1 supercar 3s. Yours looks like the tire is still covered under the fender. Perhaps 11 wheel stretching the rubber helps?

I am thinking either HR super sport all around or eibach front only.for now. Just nervous in the back. If the suspension allows enough travel. The tire will hit fender.

[Mapper]

Front shocking doesnt touch fins.
The other is rear from top down

[Tobster3]

Originally Posted by Mapper

Front shocking doesnt touch fins.
The other is rear from top down

This pic of the front is without lowering?

I’ll take a pic of mine on Wed/Thurs once I get my car back but I don’t think I’m anywhere near as close to the fins as you are. I’d be concerned about rubbing once lowering based on that pic.

[JDUNITNOW]

I have et11 and et12 for rear with Michelin ps4 and 285/295 setup. I am lowered on eibauch springs all around. I cut a few fins on driver side to alleviate rubbing.

[Mapper]

Originally Posted by Tobster3

This pic of the front is without lowering?

I’ll take a pic of mine on Wed/Thurs once I get my car back but I don’t think I’m anywhere near as close to the fins as you are. I’d be concerned about rubbing once lowering based on that pic.

Stock height (for the moment).. i did purchase the fender mesh clearance plates...
I am not as concerned with front fender fin clearance as I have the solution, than I am with the how far out the rear tires are past the fender. Maybe I am fine really dont know how.much suspension travel there is for the rear

[Mapper]

Originally Posted by JDUNITNOW

I have et11 and et12 for rear with Michelin ps4 and 285/295 setup. I am lowered on eibauch springs all around. I cut a few fins on driver side to alleviate rubbing.

What width wheels? ... looks good. I am wondering how much wider the f1 supercar 3s are compared to michelin ps4s.. might be why

[JDUNITNOW]

Originally Posted by Mapper

What width wheels? ... looks good. I am wondering how much wider the f1 supercar 3s are compared to michelin ps4s.. might be why

20 x 10 20x11

[Tobster3]

Originally Posted by Mapper

Stock height (for the moment).. i did purchase the fender mesh clearance plates...
I am not as concerned with front fender fin clearance as I have the solution, than I am with the how far out the rear tires are past the fender. Maybe I am fine really dont know how.much suspension travel there is for the rear

Which mesh clearance plates did you buy?

[Mapper]

Originally Posted by Tobster3

Which mesh clearance plates did you buy?

https://r44performance.com/products/...wheel-arch-kit

[Sp2pilot]

Originally Posted by Tobster3

Which mesh clearance plates did you buy?

Originally Posted by Mapper

https://r44performance.com/products/...wheel-arch-kit

Another (cheaper) option
https://www.aliexpress.us/item/32568...2usa4itemAdapt

[RedGTS]

Originally Posted by Tobster3

@Mapper Looks great!!

I went with the below which is very similar spec. I will be installing Eibach Front springs only.

Front - 10.5x20 ET14 285/30 R20
Rear - 11x20 ET12 295/30 R20

Only have a few pics as I took it straight from the dealer to get PPF/ tint etc.

Very nice. Which wheels are those? And are you running the Supercar 3s as well?

[Sp2pilot]

Originally Posted by RedGTS

Very nice. Which wheels are those? And are you running the Supercar 3s as well?

They looks like Edelweiss LT3

[mirob]

Originally Posted by Mapper

Wheel is a 20x10.5 ET10. Thought Id be good but with F1 supercar 3 tires I feel im out too far using 295s
What do you think?
The front are 20x10 ET12 with 285 suoercar 3 and shocking.. no rubbing on the fins.

Love the wheels! That ride height looks sus af (especially in the front). How's the ride quality? Have you checked for shipping blocks?

[Hit_Apex]

Pics look like you dropped it straight off the jack. If true, all of this feedback is a waste until you drive the care and let it settle.

[RedGTS]

Originally Posted by Sp2pilot

They looks like Edelweiss LT3

Believe you are correct. Thanks!

[greentrbo95gst]

Originally Posted by Mapper

Stock height (for the moment).. i did purchase the fender mesh clearance plates...
I am not as concerned with front fender fin clearance as I have the solution, than I am with the how far out the rear tires are past the fender. Maybe I am fine really dont know how.much suspension travel there is for the rear

Where do you get the fender mesh clearance plates from?

[Tobster3]

Originally Posted by greentrbo95gst

Where do you get the fender mesh clearance plates from?

See posts 14 and 15 above .