[W00PS]

Originally Posted by yeetyeet

That vid is for the carbon, they just placed it on the black version install directions. For some reason they don’t add the hole to mount the clip on the ABS versions. The ABS always slips over the factory pieces, and speculation, i’d say they are getting their black MP version from the same place ebay comes from.

So, just so I know, the “authentic” replica installs like the video, after removing the side blade thing right?

In contrast, the EBay one, and seemingly MHC Black simply slip over the side blade, this right?

Thanks for your response by the way.

[yeetyeet]

Originally Posted by S4boost

So, just so I know, the “authentic” replica installs like the video, after removing the side blade thing right?

In contrast, the EBay one, and seemingly MHC Black simply slip over the side blade, this right?

Thanks for your response by the way.

Yep, exactly that!

[W00PS]

Originally Posted by yeetyeet

Yep, exactly that!

Bummer

NWCarbon Haus said they use defective carbon ones to pain gloss black, 15% off the carbon price.

Might go that route. Hoping they can get me some pictures.

I think the black lip will look better with the side skirts and black rear skirts.

I have the carbon pack so I think I’ll just add a GT carbon grill and that will round out the front

[BIGW0RM]

I have the lightweight lip from EAS. Its not my favorite looking. But its a soild piece. Ive run into the crub stopper on accident a few times and that thing is ROCK solid. Scrapping going in and out of step driveways doesnt show any damage unless youlook at it from below. So thats what I went with this time.

Ive already wrecked a handful of carbon fiber ones from my E92 and F80 days that Im just over those now that I am older.

[domino_z]

I was planning to paint the genuine mperf gloss black

Has anyone done that yet

Painting cf is a bit tricky, you have to ensure you have a very good quality part so it doesn’t look all wavy once painted

[dtronics]

Originally Posted by BIGW0RM

I have the lightweight lip from EAS. Its not my favorite looking. But its a soild piece. Ive run into the crub stopper on accident a few times and that thing is ROCK solid. Scrapping going in and out of step driveways doesnt show any damage unless youlook at it from below. So thats what I went with this time.

Ive already wrecked a handful of carbon fiber ones from my E92 and F80 days that Im just over those now that I am older.

Exact same thing for me. I destroyed a bunch of carbon fiber lips on my E92 and F82. Thousands down the toilet. After ruining 2 M Performance lips on my F82 in 2 months, I went to the Lightweight lip. I scraped that thing so much but it was rock solid. Unless you got under the car with a flashlight, you couldn’t see anything.

I have all M Performance cf on my G80 except for Lightweight lip. It’s not the sexiest but good OEM+ vibes and gives the front a little something something. It sucks getting old.

[mfitzger16]

Originally Posted by unknwng80

I think you’re right, going to try to find some more cars that have it installed to confirm before ordering it

The Q&A on the site says they’ve only sold 3 as of last week. The photos they have are probably the only photos in existence lol.

For $200 I’d say it’s worth the risk. Or wait and I’ll buy one and post some pictures

[ChrisM4]

Originally Posted by mfitzger16

The Q&A on the site says they’ve only sold 3 as of last week. The photos they have are probably the only photos in existence lol.

For $200 I’d say it’s worth the risk. Or wait and I’ll buy one and post some pictures

I’m interested in this one too…is it coming from China or is it in stock in the states?

It looks good and is inexpensive.

[Greggoryy]

Originally Posted by ChrisM4

I’m interested in this one too…is it coming from China or is it in stock in the states?

It looks good and is inexpensive.

At this price points it’s probably from China and stocked in the states. I just bought one will let y’all know how well it fits.

[Greggoryy]

Received the lip and installed last night. Easy process only took 20 minutes and I didn’t need to use any hardware it came with (using 10 of the existing 10mm bolts from bottom of bumper). Quality and Fitment is great since it’s a simple 3 piece design and installs directly over without needing to remove side pieces. However, I’m not sure I dig the design, it protrudes a little too far out in my opinion and doesn’t compliment the bumper lines as well. I’ll keep it on for a few weeks and decide if I’ll keep it. What do y’all think?

[unknwng80]

Originally Posted by Greggoryy

Received the lip and installed last night. Easy process only took 20 minutes and I didn’t need to use any hardware it came with (using 10 of the existing 10mm bolts from bottom of bumper). Quality and Fitment is great since it’s a simple 3 piece design and installs directly over without needing to remove side pieces. However, I’m not sure I dig the design, it protrudes a little too far out in my opinion and doesn’t compliment the bumper lines as well. I’ll keep it on for a few weeks and decide if I’ll keep it. What do y’all think?

Fitment and finish looks great but it definitely does protrude out a bit more than I expected.

[Greggoryy]

Originally Posted by unknwng80

Fitment and finish looks great but it definitely does protrude out a bit more than I expected.

Yea it fits great no gap whatsoever.

[CMW33]

I don't think anyone has said it but Maxton Design USA's stuff fits well and is a really good value. They have a few different versions available in gloss black. I had their front lip on my A90 and was really pleased with it.

[mfitzger16]

Originally Posted by Greggoryy

Received the lip and installed last night. Easy process only took 20 minutes and I didn’t need to use any hardware it came with (using 10 of the existing 10mm bolts from bottom of bumper). Quality and Fitment is great since it’s a simple 3 piece design and installs directly over without needing to remove side pieces. However, I’m not sure I dig the design, it protrudes a little too far out in my opinion and doesn’t compliment the bumper lines as well. I’ll keep it on for a few weeks and decide if I’ll keep it. What do y’all think?

I like it! I ordered mine yesterday, so glad to know my gamble is going to pay off.

[Greggoryy]

Originally Posted by mfitzger16

I like it! I ordered mine yesterday, so glad to know my gamble is going to pay off.

After living with it for 24 hours and having the chance to view the lip from all angles, I’m starting to really like it. Looks incredibly well integrated from medium to farther distance away and the no gap fitment is a huge plus.

[unknwng80]

Originally Posted by Greggoryy

After living with it for 24 hours and having the chance to view the lip from all angles, I’m starting to really like it. Looks incredibly well integrated from medium to farther distance away and the no gap fitment is a huge plus.

Glad to hear that man! Can’t wait to get mine installed

[kgelfen360]

Originally Posted by Greggoryy

After living with it for 24 hours and having the chance to view the lip from all angles, I’m starting to really like it. Looks incredibly well integrated from medium to farther distance away and the no gap fitment is a huge plus.

Hey man sorry which lip is that ?

This one ?

https://www.aeroflowdynamics.com/pro...iABEgKZ6PD_BwE

[GolfCoyote]

AKA Motorsports fitment is good for the price

[kgelfen360]

Does anyone have MHC Gloss Black one installed and has pictures ?

https://x-ph.com/mhc-black-bmw-m3-m4...0-g81-g82-g83/


Or how about Bayoptics one?

https://bayoptiks.com/products/2021-...glossy-black-4

[Greggoryy]

Originally Posted by kgelfen360

Hey man sorry which lip is that ?

This one ?

https://www.aeroflowdynamics.com/pro...iABEgKZ6PD_BwE

Yep that’s the one. Still have it and like it a lot.

[kgelfen360]

Originally Posted by Greggoryy

Yep that’s the one. Still have it and like it a lot.

Cool thanks!! Did u have to drill anything? Fitment good? I think I might get it seems like good option considering the price

[Greggoryy]

Originally Posted by kgelfen360

Cool thanks!! Did u have to drill anything? Fitment good? I think I might get it seems like good option considering the price

No drilling just use the same 10mm bolts from the car and it’ll fit. Scraped it ~3 times already on steep curbs and driveways and still holding up.