03-23-2023, 10:00 PM | #89 |
First Lieutenant
1147
Rep 302
Posts |
Just got done installing my other set of 20". I was waiting to get them coated
|
Appreciate
6
|
03-24-2023, 09:03 PM | #90 | |
Lieutenant
1411
Rep 531
Posts |
Quote:
|
|
Appreciate
0
|
03-24-2023, 09:11 PM | #91 |
Lieutenant
1411
Rep 531
Posts |
20x10.5 et 14 285/30/20 PS4S
21x11.0 et 12 305/25/21 No rubbing at all lowered on KW HAS max low in front and max high in the rear. |
04-05-2023, 03:22 PM | #94 |
Private First Class
196
Rep 167
Posts |
20x10 285/30/20 Mps4s
20x11 305/30/20 Mps4s Lowered on AST Springs To note: if you’re xDrive, do not run a 305 rear. Not recommended at all. I’m RWD Comp so it’s fine.
__________________
IG: @nicklv_m3h
|
04-22-2023, 08:30 PM | #95 |
Lieutenant Colonel
465
Rep 1,636
Posts |
I just experimented with a BBS CHR 20x10.5 et 25 with 285 30 20 all around and it didn’t rub at full lock. I didn’t drive the car yet so hopefully it will work since these wheels are practically new. I might still go with 275 30 20 front to be safe (car is stock)
|
Appreciate
0
|
04-22-2023, 09:40 PM | #96 | |
First Lieutenant
278
Rep 305
Posts |
Quote:
|
|
Appreciate
0
|
04-23-2023, 10:34 AM | #97 |
Lieutenant Colonel
465
Rep 1,636
Posts |
Will do. To my surprise I found in the owners manual page 327- 328 ( my car is X Drive) tire pressure recommendation for 285/30/20 front and 295/25/21 for the 1000M wheels. Since I need tires anyway I might go 295/30/20 in the back. I will keep everyone posted.
|
Appreciate
1
6SPD_S58277.50 |
04-24-2023, 12:08 PM | #98 |
Lieutenant Colonel
465
Rep 1,636
Posts |
Here is a quick update. The fronts did fit with 10mm spacers with no issues the BBS wheels are 20x10.5 et25 (et 15 with spacers). It will not fit without spacers and I think 10mm is the minimum. Probably 12mm spacers will be better. I drove it around the block with no issues or rubbing. I suspect if the wheels were 20x10 it would have been a better fit. The tires are 285-30-20. I only have 3 tires on the wheels so I didn’t try the back yet. If everything goes well I will go with 285 front and 295 back with 10mm spacers all around.
Last edited by Race_Doc11; 04-26-2023 at 10:49 AM.. |
Appreciate
1
MaC-N54-E82492.50 |
04-30-2023, 08:51 PM | #99 | |
First Lieutenant
278
Rep 305
Posts |
Quote:
|
|
Appreciate
0
|
05-01-2023, 10:06 AM | #100 | |
Lieutenant Colonel
465
Rep 1,636
Posts |
I had the same issue with the BBS CHR without spacers et 25. The wheels didn’t even turn and was stuck. I realized the issue before even putting the car on the ground. I can confirm that after adding 10 mm spacers there was no rubbing any where although it looked like a tight fit only when the steering is full locked. The 285 tires are Michelin PSS and they are stretched inward because the wheels are 10.5 inches and probably that’s why it didn’t rub. When I try the BBS on the back I will check if the 20” 856 wheels will fit with spacers on the front and let you know. I’m not planning to use the oem 20” square setting I’m only going to use the BBS and keep the 856 as my winter set.
Quote:
Last edited by Race_Doc11; 05-01-2023 at 10:32 AM.. |
|
Appreciate
0
|
05-01-2023, 11:42 AM | #101 | |
First Lieutenant
278
Rep 305
Posts |
Quote:
|
|
Appreciate
0
|
05-01-2023, 02:16 PM | #102 |
Lieutenant Colonel
465
Rep 1,636
Posts |
https://g80.bimmerpost.com/forums/sh....php?t=1999871
Scroll down to post 22 the owner of that car has 20” square setup he had to cut the fender wells |
Appreciate
1
6SPD_S58277.50 |
Post Reply |
Bookmarks |
|
|