[Jhanksm3]

Got mine from aeroflow dynamics less than 200 dollars and I love it

[ChrisM4]

Originally Posted by Jhanksm3

Got mine from aeroflow dynamics less than 200 dollars and I love it

Looks great can you share a link? I’m considering the Unit17 unit but this also looks good especially for the price. Can you post side on pictures as well?

[Jhanksm3]

Originally Posted by ChrisM4

Looks great can you share a link? I’m considering the Unit17 unit but this also looks good especially for the price. Can you post side on pictures as well?

Definitely. I'll do it once I'm home and I'll pm you link

[Jhanksm3]

Here you go Chris

https://www.aeroflowdynamics.com/pro...f77ff5c9&_ss=r

[ChrisM4]

Originally Posted by Jhanksm3

Here you go Chris

https://www.aeroflowdynamics.com/pro...f77ff5c9&_ss=r

Thanks!

Can you do me a favour and measure from the ground to the bottom of the lip? Wondering how much clearance I’d have for touchless car washes.

[Jhanksm3]

Originally Posted by ChrisM4

Thanks!

Can you do me a favour and measure from the ground to the bottom of the lip? Wondering how much clearance I’d have for touchless car washes.

😆 🤣. Chris you should be hand washing anyway! Do you plan to stay on stock height?

You are lucky because my suspension comes in today and I'm changing it tonight, however before I do I'll get you a measurement

[ChrisM4]

Originally Posted by Jhanksm3

😆 🤣. Chris you should be hand washing anyway! Do you plan to stay on stock height?

You are lucky because my suspension comes in today and I'm changing it tonight, however before I do I'll get you a measurement

Thanks!

I do both I have it ceramic coated and use the touchless wash pass over the winter to keep it reasonably clean. (Hand wash once a week in the garage)

[Jhanksm3]

Originally Posted by ChrisM4

Thanks!

I do both I have it ceramic coated and use the touchless wash pass over the winter to keep it reasonably clean. (Hand wash once a week in the garage)

6 and 1/8

[ChrisM4]

Originally Posted by Jhanksm3

6 and 1/8

Thanks!

[edrielagustin]

Originally Posted by TK3pedal

Went the ultra-cheap Ebay way for this black lip. Normally I don't skimp on parts but figure it can be disposable. Worth a try. Fits fine, looks good unless you really get close.

You got a link for this by any chance?

[JDR_G80]

Installed the aeroflow front lip. Fits and looks great from a distance, but when you look at it the finish is terrible. There are a couple fish eyes, paint job looks like it was done in a backyard, and you can see the circle indents from where the three pieces are attached to each other by a small screw. Can't complain for a buck fifty I guess.

[Jfurby]

Originally Posted by unknwng80

Anyone have any recommendations for a gloss black front lip? Looking for one that doesn’t require drilling. I know there’s an eBay one that is pretty common on the forum but it’s out of stock.

Also, does anyone have pictures of the lip from Aeroflow Dynamics, NINTE, or AKAMotorsports?

I have the Maxton pro which I believe use the factory mounting points. I really like it.

[G806speed]

Rockin’ the Aeroflow. Really like it! It does scrape in places and I do fear the day it meets its demise when it runs into road debris. C'est la vie and the price is right!

[Knighthawk]

Added an Aeroflow splitter. Have already hit it in a curb and it held up well. Really ties the OEM+ look together. Seems sturdy thus far.

[mike@x-ph.com]

Originally Posted by Knighthawk

Added an Aeroflow splitter. Have already hit it in a curb and it held up well. Really ties the OEM+ look together. Seems sturdy thus far.

[Grmnmnypt]

Got the Ebay one installed. It does the trick for $140 to my front door. I would give it a 9/10 for fit and not drilling in the front bumper is a bonus. It was surprisingly nice for the money.

[Mrproper86]

Just installed the same splitter. I only used the oem hardware and the pre installed 3m tape. Didn’t wanna use the self tapping screws to drill holes into the bumber. I do occasionally a few pulls to 120-160mph . Anyone has any experience with the aeroflow dynamics splitter holding up at higher speeds with only the oem hardware installed?

[ChrisM4]

Here’s the version I installed. Fits over the stock side pieces and has great clearance. I love how it ties all the gloss together around the car now. Took me about 90mins to install on the floor in the garage. Would have been faster if I had an extra set of hands.

[Feroz_Moto]

Originally Posted by Mrproper86

Just installed the same splitter. I only used the oem hardware and the pre installed 3m tape. Didn’t wanna use the self tapping screws to drill holes into the bumber. I do occasionally a few pulls to 120-160mph . Anyone has any experience with the aeroflow dynamics splitter holding up at higher speeds with only the oem hardware installed?

I self tapped mine when I had it on and it held well up to 160. I had an M Performance version on the car with tape and only the OEM screws and the middle part flew off into the oblivion.

Looking forward to see if you did any testing without the tappers and if it held on.

[Mrproper86]

So tested the splitter multiple pulls to 120-130mph with oem hardware installed only. Also drove 1200miles on the highway and zero issues. 👍

[Moses25]

I had quality issues with my Aeroflow there indentations where the formed inserts were to join the side pieces it drove me nuts and I asked for a new one and they swore the second one was perfect and it wasn’t but at that price point hard to complain to much . I did order the AKA MP lip. for the price I’ll give it a look as well

[F80-F15]

Originally Posted by evilboi77

Here's the V-Style one i got from fleabay that i'm pretty happy with. This one replaces the front side lip.
https://www.ebay.com/itm/226047599879

I had the MP Style Gloss Black from fleabay and I didn't like the fitment.

Did you have to take out the bumper to install it? (I.e to remove the factory side slat/pieces)