03-16-2023, 11:17 AM | #1 |
Private First Class
157
Rep 126
Posts |
HELP. OpF delete
Just had the OPFs removed and installed the OPF delete cables etc.
Now the car throws up every error msg under the sun and won't rev what so ever. Any bright ideas other than bad OPF delete cables? |
03-16-2023, 12:17 PM | #2 | |
Major
884
Rep 1,319
Posts |
Quote:
I know when some folks have deleted their OPFs, and fitted the delete modules, they sometimes have to reset something with ISTA. Im not just too sure what they reset, but i remember Joe Achilles, having to do this, when he went down to Milltek, and had the OPF deletes done. Its not a big job, software related i presume, but hopefully someone else will chime in, with the exact info . PS, just give Imran a call at Evolve, he will know for sure, good luck. |
|
Appreciate
0
|
03-16-2023, 01:06 PM | #3 | |
Private First Class
157
Rep 126
Posts |
Quote:
It looks like we actually just got a bad set of delete cables that were breaking the circuit. We left them off and it all works, just the standard drive train fault up but still driveable. AutoID sorted me out immediately sending a new set to arrive tomorrow. |
|
Appreciate
0
|
03-17-2023, 09:09 AM | #4 |
Private First Class
157
Rep 126
Posts |
Here's a fun one for you.
Delete modules still off until I can fit the new ones. My system is now all 3 inch from the second cats back, x-pipe and 2 smaller individual mufflers. No faults today what so ever.. Still going to fit the miltek ones when they arrive and also have the can bus module just incase, but interesting it seems to have resloved itself.. i expected it to throw the fault again after a few mins driving / getting up to temp but nothing.. |
Appreciate
1
Jobe10188.50 |
03-17-2023, 10:42 AM | #6 |
Private First Class
157
Rep 126
Posts |
|
Appreciate
0
|
03-17-2023, 07:05 PM | #7 |
Lieutenant
285
Rep 427
Posts |
Mate, you will get limp mode as you have not deleted the opfs yet. Quite dangerous on motorways, I have been there.
When you install the delete cables and still get errors, reset the opfs in ista+: Run Ista,>> identify vehicle>>Vehicle management>>Service functions>>Power Train>>Engine electronics>>Petrol particulate filter>>Petrol particulate filter>>register replacement Delete all errors after this. Job done. |
Appreciate
0
|
03-17-2023, 10:51 PM | #8 | |
Private First Class
157
Rep 126
Posts |
Quote:
We did the Ista reset but it didn't work. It was almost definitely an issue with 1 of the cables not making the connection but hopefully the new miltek ones will work. |
|
Appreciate
1
madmedman284.50 |
02-09-2024, 10:57 AM | #11 | |
BIMMERPOST Sponsor
1912
Rep 3,153
Posts |
Quote:
ENET and WIN PC ONLY required.
__________________
Apple CarPlay Fullscreen for NBTEVO / ENTRYNAV2
GTS FLASH F8X / CS FLASH G8X / NBTEVO iDrive 4 to iDrive 6 + CarPlay Fullscreen iDrive Firmware Update + CarPlay Fullscreen -> Video Process Visit BIMMER-REMOTE.com - 10% OFF with BIMMERPOST_10 info@bimmer-remote.com or PM |
|
Appreciate
1
mathys219.00 |
05-17-2024, 05:58 AM | #13 |
BIMMERPOST Sponsor
1912
Rep 3,153
Posts |
Yes, not a problem at all to solve it
__________________
Apple CarPlay Fullscreen for NBTEVO / ENTRYNAV2
GTS FLASH F8X / CS FLASH G8X / NBTEVO iDrive 4 to iDrive 6 + CarPlay Fullscreen iDrive Firmware Update + CarPlay Fullscreen -> Video Process Visit BIMMER-REMOTE.com - 10% OFF with BIMMERPOST_10 info@bimmer-remote.com or PM |
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|